纳米水溶性金封闭剂103W
103W纳米金封闭剂是特别配制用于连续镀镀金或金镀层的水溶性耐腐蚀高盐雾防氧化剂,若把工件浸在本溶液,可形成一层约一分子厚度的有机纳米保护层,防止其他有关的氧化反应发生。
103W纳米金封闭剂含有一种可溶于水的非常活跃的镀层封孔剂,所形成的保护层无毒性和无刺激性,它可以在安全的情况下应用于珠宝、饰物、各类平面或管状器皿等。如应用于电子接插件等,对接触电阻的影响很小。
另一方面,焊接性能也不会在任何情况下有所影响。
一·操作条件
|
|
范围 |
最佳 |
103W纳米金封闭剂 |
ml/L |
50~100 |
60 |
温度 |
℃ |
45~55 |
50 |
浸渍时间 PH |
min |
0.25~2.0 2.2~2.7 |
0.5 2.4 |
二·溶液配制
注意:使用103W纳米金封闭剂前,必须摇匀,如储存温度低于25℃,103W纳米金封闭剂会部份固化,必须把容器放在50℃左右温水内,浓缩液便会变成透明黄橙色液体。
1、 彻底清洗镀槽;
2、 加入75%体积的纯水,加热至操作温度;
3、 慢慢搅拌下,加入103W纳米金封闭剂,并搅拌均匀;
4、 加纯水标准体积,搅拌均匀;
5、 调整操作温度,溶液可以使用。
三·使用方法
1、 将干燥或湿润的已清洁或活化的工件浸于保护液内,保护液的温度约为50℃,浸渍时间0.25~2.0min;
2、 在温暖纯水(35~55℃)或除油剂内清洗0.5~1.0min;
3、 在纯水中冲洗2~5min;(非常重要)
4、 清洗干净后可干燥。
四·溶液维护及补充
如果保护冷却一段时间或停用稍长时间,则保护剂会分层,但加热后则会恢复正常,经常以纯水补充蒸发损失。如要过到理想的保护效果,请经常保持103W在100%工作浓度。
五·所需设备
槽 |
用不锈钢、PP、PVC、PVDC或高密度衬里的槽子 |
通风 |
需要 |
加热 |
PTFE类比较适合 |
搅拌 |
利用水泵进行循环搅拌 |
过滤 |
不需要 |
六·故障处理
现象 |
原因 |
改善措施 |
有痕迹或条纹 |
预清洗不理想 |
保证所有进入103W纳米金封闭剂溶液内的工件已彻底清洗 |
水洗槽被污染 |
以温水洗代替或增加水流速度 |
|
工件未能通过防腐试验 |
测试103W封闭剂浓度 |
调整103W纳米金封闭剂至标准浓度 |
检查温度和PH |
调整温度和PH |
|
浸渍时间太短 |
增加浸渍时间 |
|
水洗温度高于60℃ |
降低温度至45-55℃ |
AUTRONEX® NANO 103W (Provisional)
A Hole-Plug Solution for Gold Plated Surfaces
INTRODUCTION
AUTRONEX NANO 103W is a water base formula designed for THINNER gold with better
corrosion resistance and improved lubricity. AUTRONEX NANO 103W can coat an ultra thin
organic film on gold with thickness of a few nanometers and plug all holes on gold surface.
AUTRONEX NANO 103W is formulated as a ready for use solution; the working solution consists
of a few highly active oxidation inhibitors dissolved in a water based system. The film is non-
poisonous, non irritant and can be safely applied to gold and gold alloy surfaces. Because the ultra
thin film has a strong lubricating effect on contacts and at the same time hardly influences electrical
contact resistance, a treatment with AUTRONEX NANO 103W is suitable for electrical contacts and
other electronic components. Solderability is unaffected.
* chemically stable film
* easy operation
* non-hazardous
* decorative and electronics
OPERATING CONDITIONS
Range Optimum
Temperature 45-55 °C 50 °C
pH 2.2-2.7 2.4
Treatment time 15-120 sec. 30 sec.
EQUIPMENT REQUIRED
Tanks
Constructed of, polypropylene, PVC, PVDC, linear polypropylene or high density polyethylene.
Fume extraction
Recommended
Heaters
Preferably PTFE. Heaters must be fitted with low solution level cut outs and an earth leakage circuit
breaker.
Agitation
Preferably by pumping.
Filtration
Not recommended.
INITIAL MAKE-UP OF THE SOLUTION
1. Ensure that the tank is thoroughly cleaned before installing AUTRONEX NANO 103W.
2. AUTRONEX NANO 103W is a ready for use solution.
3. Heat the solution to the correct operating temperature.
4. Ensure that the temperature is within the correct operating range.
5. The bath is now ready to use.
OPERATION SEQUENCE
Temp. Time
AUTRONEX NANO 103W 45-55 °C 15-120 sec.
Rinse with D. I. Water RT 30 sec
Compressed air dry 10 Sec
WASTE TREATMENT
Spent AUTRONEX NANO 103W solutions contain organics, mainly surfactants contributing to
COD values. A detailed waste treatment procedure is available on request.
HANDLING AND SAFETY INSTRUCTIONS
For detailed information consult the material safety data sheets for this product.
Please read material safety data sheets carefully before using this product.
DISCLAIMER
All recommendations and suggestions in this bulletin concerning the use of our products are based
upon tests and data believed to be reliable. Since the actual use by others is beyond our control, no
guarantee expressed or implied, is made by Hanxu., its subsidiaries of distributors, as to the
effects of such use or results to be obtained, nor is any information to be construed as a
recommendation to infringe any patent.